manualshive.com logo in svg

Tri-Clover 741 Series, Service & Installation Manual

Share
Download
Tri-Clover 741 Series Service & Installation Manual Download Page 17

- 17 -

MAINTENANCE

Type 15/25 Actuator Replacement Parts

ASSEMBLY

1

Clamp the Inner Diaphragm Guide in a vise with its threaded stud facing upward.

2

Set the diaphragm into the Inner Guide, set the Inner Diaphragm Clamp inside the diaphragm,
screw on the Nut until hand tight.  Thread on the adapter and tighten to 15 ft.-lbs.

3

Lubricate the diaphragm inside and outside completely with L1011 Sanitary Silicone Spray.
Roll the diaphragm onto outer diaphragm clamp.  Slide body insert onto outer diaphragm
retainer.

4

Carefully slide diaphragm assembly into cylinder.  Do Not scratch, tear or abrade diaphragm.

5

Install sealing nut, gasket and air coupler adapter.

6

Clamp bonnet into vise locating on the four mounting bolts.  Place spring into bonnet.

7

Lubricate the cylinder threads with Tri-Clover C137.  This will help prevent the threads from
galling.  Place cylinder assembly onto spring.

To prevent injury, compress spring by hand and thread cylinder onto
bonnet for at least 3 complete turns.  Apply a strap wrench to
cylinder and tighten until it "bottoms" onto bonnet.

CAUTION

8

Remove actuator from vise.  Insert packing and bushing into counter bores on bonnet.

9

Apply Removable Loctite* to the fine threads of the actuator stem. Push actuator stem through
bonnet and thread into adapter.  Fasten completely with a wrench using stem flats.

(*Loctite is a registered trademark of Loctite Corporation)

Part Number

Qty

Description

1

37-5-S

1

Coupler

2

17-88

1

Gasket

3

13-78-S

1

Sealing Nut

4

25-263B-01-S

1

Body

5

36-55

1

Outer Diaphragm
Clamp

6

37-88

1

Body Insert

7

35-1

1

Diaphragm

8

36-3

1

Inner Diaphragm
Clamp

9

37-89-316

1

Adapter

10

4-2-S

1

Spring

11

19-1279-S

1

Stem

12

12-497-S

1

Bonnet

13

36-15

1

Inner Diaphragm
Guide

14

13-15

1

Nut

15

17-98

1

Packing

16

25-428-05

1

Seal Retainer

Summary of Contents for 741 Series
































Reviews:

No comments

Brands by name

Popular brands

Load more brands