Treyco 3000 Instruction Manual Download Page 9 | Manualshive

Page: 9 / 17

Treyco 3000 Instruction Manual Download Page 9

Page 8

4.

Apply honing powder evenly on disc with supplied shaker covering the disc
lightly (approximately 1-2 teaspoons).

5.

Place wooden charging stick on honing disc in line with center of disc and
narrow edge of stick on honing disc. Make two revolutions around honing disc
with charging stick to evenly distribute honing powder. Apply light down
pressure on charging stick. This will fill the fine grooves on disc with powder.

6.

Mount Oster comb blade size 10 or 15 on holder engraved OSTER COMB.

7.

Turn on honing disc and automatic arms.

8.

Lower comb blade only gently onto honing disc placing it down when blade is
centered between outer edge and inner edge (do not set blade down at inner or
outer edges of disc).

9.

Let blade make 4-6 complete strokes across disc.

10.

Lift blade to upright position.

11.

Repeat this process FIVE more times.

12.

After repeating this process, the entire surface of disc should be a uniform dull
gray in color.

CHARGING STICK

«
...
7
8
9
10
11
...
»

Summary of Contents for 3000


















Reviews:

No comments