Treyco 3000 Instruction Manual Download Page 17 | Manualshive

Page: 17 / 17

Treyco 3000 Instruction Manual Download Page 17

Page 16

CENTER HOLDERS

Raise arms to vertical position.
Mount an A-5 comb blade size 10 or 15 on Comb Holder.
Lower arm so comb blade is resting on top of honing disc.
Turn on automatic arms (switch on left) and observe if the comb blade overlaps the
inner and outer edge of honing disc the same amount at each end of its stroke.
If not, turn off automatic arms.
Remove plastic cover from screw hole on top of arm rest and loosen set screw.
Move pivot block assembly left or right on slide rod bearing housing so teeth of
cutter overlap same on inner and outer edge of disc.
Verify by turning on arm motor, replace plastic cover in screw hole cover.
Repeat above step until comb overlaps inner and outer edges of honing disc
equally.
Repeat process on cutter blade holder.

ADJUSTMENT OF HOLDERS TO CENTERLINE OF DISC

Loosen set screw collars on arms and slide holders on arms so the teeth of the
cutter and comb are in line with centerline of honing disc.

Set screw collars

Centerline of honing disc

«
...
15
16
17

Summary of Contents for 3000


















Reviews:

No comments