17
-
The button twinkles. There is a short phase of water loading, then the coffee comes out from spouts (22).
-
Once the desired quantity has been reached, press the flashing button again to stop dispensing.
WARNING
: do not remove the filter holder during function. At the end of erogation, wait 10 seconds before
removing the filter holder.
Remove slowly the filter holder to avoid splashing.
-
At the end of dispensing, the lights remain on and you can make another coffee.
-
When removing the filter holder, the pod may remain attached to the seat of the filter holder (13). To
remove it, tilt the filter holder down, or remove it gently with a knife.
-
If use is finished, turn off the machine with the button (7).
MAKE MILK FOAM FOR COFFEE
-
Prepare coffee as described before, using an espresso cup if you want to prepare a macchiato, or a bigger
cup if you want a cappuccino.
-
Put whole milk in a stainless steel jug, filling one third of the capacity.
-
Press steam button (11 -
). The light of steam twinkles to indicate that the appliance is heating, and then
they stay on when the appliance is ready. The thermometer (12) is in the blue area.
CAUTION, Risk of burning: during steam erogation, do not direct the jet towards yourself or towards
other people. Only handle the tube by the rubber part: do not touch metal parts.
-
Direct the steam erogation tube (5) in an empty container, then rotate knob (3) anti-clockwise: some water
will be released first and then steam. Stop steam jet rotating back the knob “0”.
-
Direct the steam erogation tube (5) in the jug, immersing well the tube in the milk.
-
Rotate knob (3) anti-clockwise: tube will start dispensing steam.
-
During steam erogation, move and rotate the jug in order to let the jet arrive to all the milk.
-
When you see foam in the jug, milk is frothed. Stop steam jet rotating back the knob “0”.
-
Pour the foam of milk in the cup of coffee prepared before.
WARNING
: after every use of the tube (5), erogate steam for some seconds, in order to keep the steam tube
clean of milk residues, and clean the tube (5) with a damp cloth.
LOWER THE TEMPERATURE AFTER USE OF THE STEAM JET
Steam requires a higher temperature respect to coffee. To prepare a coffee (or dispense hot water) after
dispensing steam, lower the temperature and return the thermometer to the green area.
-
Press one of the coffee preparation buttons (9 -
) or (10 -
). The lights of buttons twinkle to indicate
that the appliance is cooling, and then they stay on when the appliance is ready.
-
To make the temperature go down more fastly, you have to release some steam.
-
Direct the steam erogation tube (5) in an empty container, then rotate knob (3) anti-clockwise: water
mixed with steam will be released.
-
When the lights of buttons stop flashing and remain steady, the temperature has dropped sufficiently and
the machine is ready to make coffee. Stop the steam by turning the knob to “0”.
DISPENSE HOT WATER
-
Switch on the machine in coffee dispensing mode (with thermometer in green zone).
CAUTION, Risk of burning: during hot water erogation, do not direct the jet towards yourself or
towards other people. Only handle the tube by the rubber part: do not touch metal parts.
-
Direct the steam erogation tube (5) in a cup, then rotate knob (3) anti-clockwise: hot water is released.
When the desired amount of water has been obtained, stop steam jet rotating back the knob “0”.
EMPTY CONTAINER AND EVENTUAL PUMP BLOCK
Please avoid to finish water in the container, but in case it happens:
-
When the water runs out, the machine makes a loud and unusual noise. Turn off immediately and pour
water in the tank. At the next restart, the pump may not load the water correctly. To help fill the water it is
recommended to dispense hot water from the tube (5).
-
Direct the steam erogation tube (5) in a cup, then rotate knob (3) anti-clockwise water or steam is
released. Stop steam jet rotating back the knob “0”.
