manualshive.com logo in svg

TRENDnet TEG-S2400I - DATA SHEETS, User Manual, Page: 29 / 149

Share
Download
TRENDnet TEG-S2400I - DATA SHEETS User Manual Download Page 29

- 29 - 

supports LACP, the LACP dynamic trunking group will be created automatically.   

4.

 

Work ports: 

Allow max four ports can be aggregated at the same time. If LACP static trunking 

group, the exceed ports is standby and able to aggregate if work ports fail. If local static trunking 

group, the number must be as same as the group member ports.   

5.

 

Select the ports to join the trunking group. Allow max four ports can be aggregated at the same time.   

6.

 

If LACP enable, you can configure LACP Active/Passive status in each port on State Activity page.   

7.

 

Click Apply.   

 

2.5.5.2 Aggregator Information   

When you are setting LACP aggregator, you can see relation information in here.   

1.

 

This page is no group active. LACP don’t working.   

 

 

 

2.

 

This page is Static Trunking groups.   

 

 

3. 

This page is Actor and Partner trunking one group.

 

Summary of Contents for TEG-S2400I - DATA SHEETS






















































































































































Reviews:

No comments