background image

5

EN

M

use GP

 

minipool

2

ChECkIng MInIPool InTEgrITy

After having removed the minipool from the packing, check its integrity.

Check:

•  That there is no visible structural damage;

•  That there are no cracks in the surface of the minipool or in the outer covering (cracks due to incorrect transport 

or support are not covered by the warranty);

•  The correct position of the sleeves and pipes;

•  That any ties are not loosened.

If you notice any anomalies, do not proceed with the installation but rather promptly contact the Manufacturer.

Preliminary operations

1

PrEPArATIonS AnD ChoICE 

oF PoSITIon

The pre-installation sheet supplied at the time 

of purchase provides all the information neces-

sary for a correct preparation of the installation 

environments.

Before installing the minipool, check that everything 

has been prepared.

 Find below a quick checklist, for 

complete information always refer to the pre-installation 

sheet.

Check that:

•  A platform or a recess (in the case of recessed installa-

tions) of reinforced concrete, with a minimum thickness 

of 10 cm, has been created, perfectly flat and suitable 

for supporting the weight of the minipool and the 

people within.

•  Ø15 cm vents have been installed to ensure proper 

ventilation of the technical compartment.

•  Drainage grating around the perimeter has been 

installed to help preserve the equipment and the 

structure (even for indoor installations);

•  Non-slip flooring has been installed in the area around 

the minipool;

•  For a recessed installation, 

a technical inspection port 

measuring at least 50 cm wide has been prepared on 
all sides of the minipool

;

•  The connections to the electrical grid have been made 

in compliance with current regulations in force in the 

country of installation;

•  A water softener has been installed for the water used 

to fill the minipool if the water has a high degree of 

hardness;

•  For outdoor recessed versions, the walls have been 

insulated to protect against the cold.

More information

ouTDoor InSTAllATIon

Preparations

To run the electric cables from the main electrical panel 

to the minipool underground ducts must be used and 

adequately protected against freezing by using insula-

tion. It is also recommended to add drainage points in 

them to prevent standing water.

Choice of position

: take into account the proximity of 

trees or hedges, and note that debris (e.g., leaves) can 

cause damage to the equipment over time that is not 

covered by warranty and make maintenance more ex-

pensive and frequent. It is also recommended to always 

install flooring around the minipool, possibly anti-slip.

InDoor InSTAllATIon

Preparations

: in the area used to access the minipool 

it is recommended to install anti-slip flooring.

The evaporation of water in the minipool in the pres-

ence of high internal temperatures can generate very 

high levels of humidity in the environment.

To avoid this problem, provide good natural or forced 

ventilation in the installation environment and, if nec-

essary, a dehumidification system. Damage caused by 

this phenomenon is not covered by the manufacturer 

warranty.

Choice of position

: Always take into account the size 

of the minipool: narrow passages, doors and steps can 

be an obstacle to its transport to the desired place.

Summary of Contents for Muse GP

























Reviews: