background image

14 

Target Recovery 

Once you have established the exact location of the target, the next step is to dig a small 
hole to recover it.  In order to preserve the environment and keep from having areas 

closed to metal detecting, it is essential to make the hole as small as possible and always 

replace the soil / grass before moving on. 

Recommended tools for target recovery include a sand scoop when searching sandy areas 
or a small knife / small gardening trowel when searching grassy areas such as parks, 

schools, private yards or ball fields. 

To recover a target from grassy areas, use a sharp tool (knife / trowel) and cut a plug 

leaving a portion connected.  Fold the plug out of the hole and pass the search coil over 
both the plug and the hole to determine where the target is.  If the target is still in the 

hole, start removing dirt and place it on a sheet of plastic or a rag which makes it easier 

to replace the loose dirt when you have found the target.  Once you have recovered the 
target, check the hole to ensure there are no additional targets before refilling the hole. 

Put the loose dirt back in the hole, fold the plug back in-place and step down on the area 
to compact the soil. 

TIP

: The use of an electronic pinpointer probe will reduce the time it takes to locate and 

recover targets.  This is an accessory that most treasure hunters have found to be 

invaluable and is highly recommended. 

Detecting Tips 

Your success will increase as you gain experience in the field but the following tips can 
help you shorten the learning curve and reduce frustration that may arise. 

The search coil must be moving in order to detect a target; however, only a slight
motion is required.  If you stop moving the coil, the signal will be lost.

At times you might receive a signal from a target that is not repeatable and
produces varying audio signals.  This may be caused by trash or multiple targets

beneath the coil.  Switch to the ALL METAL mode and sweep the coil across the

target area in different directions to see if you can isolate the signals.  If you
determine that there is more than one target present, switch back to the

DISCRIMINATION or NOTCH mode and try sweeping the coil at different angles to
avoid going over more than one target at a time.  This will allow you to identify

each one and determine if it is worth recovering.

If the trash in an area is so much that you are getting numerous choppy or non-
repeatable signals, you can improve performance of the detector by slowing your

sweep speed down or reducing the Sensitivity level.

Summary of Contents for TC1X

























Reviews: