background image

16 • SLASH  VXL

To prevent loss of radio 
range do not kink or cut the 
black wire, do not bend or 
cut the metal tip, and do not 
bend or cut the white wire at 
the end of the metal tip.

Correct

No

No

No

TRAXXAS TQ

i

 RADIO & VELINEON POWER SYSTEM

TRAXXAS STABILITY MANAGEMENT (TSM)

Traxxas Stability Management or 
TSM allows you to experience all 
the speed and acceleration that 
was engineered into your Traxxas 
model by helping you to maintain 

control of the vehicle in low-traction situations. TSM helps provide 
straight ahead full-throttle acceleration on slippery surfaces, 
without fishtailing, spinouts, or loss of control. TSM also dramatically 
improves braking control. High speed cornering and control is also 
made possible as TSM makes corrections for you, without intruding 
on your fun, or creating unexpected side effects.
The Multi-Function knob on 
the TQi transmitter has been 
programmed to control TSM. The 
recommended (default) setting 
for TSM is to rotate the knob to 
the 12:00 position (the zero mark 
on the dial). 
Turn the knob clockwise to 
increase stability; turn the 
knob counterclockwise to 
decrease stability. Turn the knob 
counterclockwise to its stop to 
turn TSM completely off.  

Note: 

TSM is deactivated 

automatically when driving or 
braking in reverse. 
When driving on surfaces with 
some traction, decrease the TSM 
setting to allow the vehicle to feel more “loose” for power sliding, 
drifting, and so on. On surfaces with very little traction (loose dirt, 
smooth concrete, ice/snow), increase TSM to maximize acceleration 
and control. 
Drive with TSM on and off to test how it is making your control of 
the vehicle easier and more precise. For more information, visit 
Traxxas.com/tsm.

Note: 

TSM must be completely turned off while adjusting steering 

trim.

SETTING UP THE ANTENNA

The receiver antenna has been set up and 
installed from the factory. 

When reinstalling the antenna, first slide 
the antenna wire into the bottom of the 
antenna tube until the white tip of the 
antenna is at the top of the tube under 
the black cap. Insert the base of the tube 
into the antenna post. Take care not to 
crimp the antenna wire. Slide the crimp 
nut over the antenna tube and screw it 
onto the antenna post. Use the supplied 
tool to tighten the crimp nut on the post 
just until the antenna tube is securely 
in place. Do not over tighten or crush 
the antenna wire against the chassis. 

Do 

not bend or kink the antenna wire! See 
the sidebar for more information. Do not 
shorten the antenna tube. The minimum 
height is 62mm.

Antenna 

Tip

Antenna 

Tube

Antenna 

Wrench

Antenna 

Crimp Nut

Antenna 

Post

Recommended setting

Decrease 

stability

Increase 

stability

TSM off

Summary of Contents for SLASH VXL 58076-21



































Reviews: