ACUVANCE XARVIX XX Скачать руководство пользователя

Страница: 1 / 12

XARVIS XX Owner's Manual

Repair Conditions

Note that if the date and location of ESC purchase are not entered on the warranty card, you will

be charged for repairs even within the warranty term.

●

If a failure occurs within three months of purchasing the ESC, write the symptoms of the problem

and operating conditions in the section below and attach this to the product. For repair, send the

ESC to the distributor where you purchased the product or directly to ACUVANCE (Technical

Service Department).

●

ACUVANCE assumes no responsibility for damage or losses that occur during transportation.

Please take note of this beforehand.

●

When listing the symptoms for a repair request, you can conveniently use the repair request

sheet on the ACUVANCE homepage and then send this along with the warranty card.
(Click the “repair” section located in the upper-right side of our website. Then click “repair

request sheet”, located on the left side.)

Warranty

Item

Manufacture

no.

XARVIS XX

Purchase

date

Customer

Address

E-mail

Phone

number

Name

Warranty

term

3 months from purchase date

Phone no.

(

)

Repair card

1. Symptoms

Write the symptoms of the problem,

giving as much detail as possible.

2. Payment for repair charges

I would like to be contacted if there is compensation

※

Though it depends on the details of the repair, indicating in advance that no contact is necessary will

normally shorten the time is takes to complete the repair.

1. Parts that can be repaired.:

•Internal electronic circuitry

Damage caused by incorrect connection, inter-terminal shorting, or driving is not covered by

warranty.

2. Note that this device will not be covered under warranty if the housing has been opened.

3. ACUVANCE assumes no responsibility for damage to the receiver or servo caused by the

incorrect connection of this product.

4. Note that if the repair card (located below) or the repair sheet (on the homepage) is not properly

filled out, repair and return of the ESC may be delayed.

(M/D/Y)

Shop name (address, and phone. no.)

7F, Shin-Osaka Marubiru Annex 1-18-22

Higashinakajima Higashiyodogawa-ku

Osaka 533-0033 Japan.

FAX +81-6-6379-1190
www.acuvance.co.jp/english

Technical Service Dept.

330290-1

Содержание XARVIX XX













Результаты поиска

Содержание XARVIX XX

Отзывы:

Похожие инструкции для XARVIX XX

Бренды по названию

Популярные бренды

ACUVANCE XARVIX XX, Руководство пользователя

Результаты поиска

Содержание XARVIX XX

Отзывы:

Похожие инструкции для XARVIX XX

Бренды по названию

Популярные бренды