Travis Industries 99300677 Installation Instructions Manual Download Page 5

Page: 5 / 10

Remote Thermostat Installation Instructions

(See list below for compatible models - 99300677)

Page 5 of 6

9/28/05

Travis Industries, Inc.

Receiver Installation - Sweet Dreams

The optional blower (99000158) must be installed prior to installation

Remove and discard this
molex connector on the
wiring harness.

Attach the molex on the receiver to the connector on the wiring harness.
Insert the receiver into the mounting bracket. Place the bracket on the
back of the stove near the bottom (magnets hold it in place).

Make sure the power is

disconnected!

Thread the molex connector on the wiring
harness through this hole near the power
cord (remove the access panel if
necessary).

Receiver Installation - 864TRV

The optional blower (99000156) must be installed prior to installation

AAAAAAAAAAAAAAAAAAAAAAAAAAAA

Place the receiver in a location to

the left of the gas control valve

(near the front of the fireplae).

Connect the receiver to the

molex connector on the wiring

harness.

Remove and discard this molex

connector attached to the

blower wiring harness.

Summary of Contents for 99300677











Search results

Summary of Contents for 99300677

Reviews:

Related manuals for 99300677

Brands by name

Popular brands

Travis Industries 99300677, Installation Instructions Manual

Search results

Summary of Contents for 99300677

Reviews:

Related manuals for 99300677

Brands by name

Popular brands