TransTel Communications Superkey Series User Manual Download Page 7

Issue 2.0  December, 1995 

Off Hook Voice Announce 

Description:

  Off Hook Voice Announce allows a single line station 

users to utilize the Off Hook Voice Announce Feature 

that  is  available  to  Superkey  Electronic  Telephone 

Sets  that  are  wired  and  programmed  to  accept  Off 

Hook  Voice  Announcements.   With  this  feature,  you 

may   route   your   intercom   call   directly   to   the 

speakerphone of a busy Superkey Electronic Set. 

 

1.  Dial the desired station number. 

2.  When busy tone is returned, press [1]. 

3.  If the called station is on a handset call, you will hear a tone burst 

and be connected directly to the speakerphone of the called party. 

4.  If the called station is on a Speakerphone call, you will continue to 

hear busy tone.

 

Operator Access 

Description:

  Superkey

®

  systems  may  have  one  or  more  stations 

designated as system operators. 

1.  Lift Handset. 

2.  Dial 

[0]

3.  The station programmed as your operator will ring. 

 

Note

:  The  actual  digit  dialed  is  under  system  programming control 

and  may  be  either 

[0]

  or 

[9]

.    Check  with  your  system 

administrator if you have any doubt.

 

14 

Call Forwarding 

Description:

  Call Forwarding allows a station user to have his calls 

re-routed  to  another  station  within the  system  based 

on several different conditions. 

 

Types:  All Calls (Always) 

 

 

Busy 

 

No Answer 

 

 

 

Busy/No Answer 

 

To program call forwarding on your telephone:

 

 

1.  Lift Handset. 

2.  Dial 

[7]

[0]

[1]

3.   Dial the code for the type of forwarding that you want to activate: 

 

 

[1]

 = All Calls 

 

[2] 

= Busy 

 

[3]

 = No Answer 

 

[4]

 = Busy/No Answer 

4.  Dial  the  station  number  where  you  want  your  forwarded  calls  to 

ring. 

5  You  will  hear  new  dial  tone,  indicating  that  you  have  correctly 

programmed your telephone.  You may hang up.  Your telephone 

is now forwarded. 

 

To remove call forwarding from your telephone:

 

 

 

Repeat step 1 through 3 above.  In step 4 above, enter your own 

station   number   instead   of   another   station   number.     Your 

telephone will now operate normally. 

 

Note:

  When  your  telephone  is  programmed  for  Call  Forward  All 

Calls,  you  will  receive  interrupted  dial  tone  when  you  go  off 

hook.    This  is  an  indication  that  your  telephone  cannot  be 

reached.    This  will  also  occur  when  your  telephone  is  in  Do 

Not Disturb.

 

Summary of Contents for Superkey Series













Reviews: