Transition Networks SISTM10xx-162-LR Installation Manual Download Page 2

Page: 2 / 57

Notice

This manual contents are based on the below table listing software kernel version, hardware version,

and firmware version. If the switch functions have any different from the manual contents description,

please contact Transition Networks for more information.

Firmware Version

v1.02

Kernel Version

v3.22

Hardware Version

A5.00

FCC Warning

This Equipment has been tested and found to comply with the limits for a Class-A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

Summary of Contents for SISTM10xx-162-LR


























































Search results

Summary of Contents for SISTM10xx-162-LR

Reviews:

Related manuals for SISTM10xx-162-LR

Brands by name

Popular brands

Transition Networks SISTM10xx-162-LR, Installation Manual

Search results

Summary of Contents for SISTM10xx-162-LR

Reviews:

Related manuals for SISTM10xx-162-LR

Brands by name

Popular brands