background image

24

CPSMC19xx-100 PointSystem

chassis

po
wer suppl

y

3.5

Optional Fan Module

The optional fan module (CPSFM-200) can be installed in the extra installation
space in the back of the CPSMC19xx-100 chassis to provide additional cooling for
the entire chassis.  

CAUTION:  Wear a grounding device and observe electrostatic discharge precau-
tions when installing the fan module into the chassis.  Failure to observe this cau-
tion could result in damage to, and subsequent failure of, the fan module.

NOTE:  

The fan module can be hot-swapped.

To install the fan module into the CPSMC19xx-100 chassis:

1. Remove the protective plate from the installation slot by removing and retain-

ing the two (2) screws that secure the plate to the chassis.

2. Carefully slide the fan module into the installation slot, aligning the module

with the installation guides.  Ensure the module is firmly seated inside the
chassis.

3. Carefully install the two (2) retained screws through the fan module into the

chassis, rotating clockwise to secure.  

4. Verify that the fan module is powered by observing the fan operation.  

24-hour Technical Support:

1-800-260-1312

-- International: 

00-1-952-941-7600

I
0

I
0

Summary of Contents for PointSystem CPSMC1900-100









































Reviews: