background image

Transition Networks, Inc. 

 

 

 

 

 

M/GE-PSW-xX-01 User Guide 

33398 Rev. D 

https://www.transition.com/ 

Page 11 of 15 

Technical Specifications 

For Transition Networks M/GE-PSW-SX-01 or equivalent: 

Standards  

IEEE 802.3 

Data rate 

10 Mb/s, 100 Mbps, 1000 Mbps 

Dimensions 

1.8"W x 3.35"D x 0.85"H (45.7 x 85.1 x 21.6 mm) 

Weight 

3.15 oz. (127.5 g) approximately 
Shipping Weight 2 lbs. [0.90 kg] 

MTBF* 

24,466 hours (MIL217F2 V5.0) (MIL-HDBD-217F) 
100,130 hours (Bellcore7 V5.0) 

Memory 

1Mb 

MAC addresses 

8K 

Max Frame Size 

Up to 10,240 bytes 

Power Supply 

Unit accepts 4.5 VDC to 28 VDC 
Wall Mount AC adapter: 12 VDC 400mA 

Power consumption 

262mA @ 12VDC, 3.15 watts 

Operating

 

Temp**  

0°C to +50°C (32°F to 122°F ) 

Storage Temp 

-15°C to+ 65°C (5°F to 149°F) 

Humidity 

5% to 95%, non-condensing 

Altitude 

0 to 10,000 feet 

Certifications 

Safety: Wall Mount Power Supply, UL Listed, cUL Listed  
FCC Class A, CISPR22/EN55022 
Class A, EN55024, CE Mark 

Warranty  

Lifetime 

 

 *MTBF is estimated using the predictability method. This method is based on MIL-217F at 25°C ambient 
temperature, typical enclosure heat rise of 10°C with nominal operating conditions and parameters. 
Installation and configuration specific MTBF estimates are available upon request. Contact Technical 
Support. 
** Man

ufacturer’s 

maximum rated ambient temperature (TMRA). 

The product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable 
at the date of manufacture. 
WARNING: Visible and invisible laser radiation when open. Do not stare into the beam or view the beam 
directly with optical instruments. Failure to observe this warning could result in an eye injury or 
blindness. 
WARNING: Use of controls, adjustments or the performance of procedures other than those specified 
herein may result in hazardous radiation exposure. 
Copper based media ports such as Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3, 
Video Coax, etc., are intended to be connected to intra-building (inside plant) link segments that are not 
subject to lightening transients or power faults, and are NOT to be connected to inter-building (outside 
plant) link segments that are subject to lightening transients or power faults. 

Summary of Contents for M/GE-PSW-LX-01
















Reviews: