12
CGETF10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Cable Specifications
-- Continued
Fiber cable
- Continued
CGETF1029-112
1310nm TX / 1550nm RX single mode
CGETF1029-113
1550nm TX / 1310nm RX single mode
Fiber-optic Transmitter Power:
min: -3.0 dBm
max: +2.0 dBm
Fiber-optic Receiver Sensitivity:
min: -23.0 dBm
max: -3.0 dBm
Link Budget:
20.0 dB
CGETF1029-116
1510nm TX / 1590nm RX single mode
CGETF1029-117
1590nm TX / 1510nm RX single mode
Fiber-optic Transmitter Power:
min: -2.0 dBm
max: +3.0 dBm
Fiber-optic Receiver Sensitivity:
min: -26.0 dBm
max: -3.0 dBm
Link Budget:
24.0 dB
Copper cable
(Category 5 -- minimum requirement)
• Gauge = 24 to 22 AWG; Attenuation = 22.0 dB /100m @ 100 MHz
• Straight-through OR crossover cable may be used.
• Shielded twisted-pair (STP) OR unshielded twisted-pair (UTP) may be used
• All pin pairs
(1&2, 3&6, 4&5, 7&8)
are active in a gigabit network.
• Use only dedicated wire pairs for the active pins; e.g., blue/white & white/blue,
orange/white & white/orange, etc.
• Do not use flat or silver satin wire.
13
[email protected] -- Click the “Transition Now” link for a live Web chat.
Technical Specifications
For Transition Networks’ Model CGETF10xx-1xx or equivalent
Standards:
IEEE 802.3ab™, IEEE 802.3 2000
Data Rate / Delay:
1000 Mbs/300 nsec
Dimensions:
3.4" x 1.0" x 5.0"
(86mm x 25mm x 127mm)
Weight:
3 oz.
(91 g)
approximately
Power Consumption:
5.4W 450mA @ 12VDC
Packet Size:
10 Kbytes
(maximum)
MTBF*
381,000 hours
(MIL217F2 V5.0) (MIL-HDBK-217F)
1,344,000 hours (
Bellcore7 V5.0)
Operating Temp:
Tmar** 0°C to 50°C (
32°F to 122°F)
Storage Temp:
-15°C to 65°C
(5°F to 149°F)
Humidity:
10% to 90%, non condensing
Altitude:
0 to 10,000 feet
Warranty:
Lifetime
*MTBF is estimated using the predictability method. This method is based on MIL-217F at 25°C
ambient temperature, typical enclosure heat rise of 10°C, and nominal operating conditions and
parameters. Installation and configuration specific MTBF estimates are available upon request.
Contact Technical Support.
**Manufacturer’s rated ambient temperature.
For the most up-to-date information on the CGETF10xx-1xx media converter, view the user’s
guide on-line at: www.transition.com.
The fiber optic transmitters on this device meet Class I Laser safety requirements per IEC-
825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.
WARNING: Visible and invisible laser radiation when open. Do not stare into the beam or view
the beam directly with optical instruments. Failure to observe this warning could result in an eye
injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other than those
specified herein may result in hazardous radiation exposure.
IMPORTANT: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232,
RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected to intra-building
(inside plant)
link segments that are not subject to lightening transients or power faults. Copper-
based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3,
Video Coax, etc., are NOT to be connected to inter-building (
outside plant)
link segments that are
subject to lightening transients or power faults.
