Transcell Technology TI-1680 Setup And Operation Manual Download

Page: 2 / 47

TABLE OF CONTENTS

Page

INTRODUCTION

................................................................................................................................................. 1

FCC NOTE

........................................................................................................................................................... 1

INSTALLATION

................................................................................................................................................... 1

PREPARATION ................................................................................................................................................ 1

CONNECTIONS ................................................................................................................................................ 2

CONNECTING THE WEIGH PLATFORM ....................................................................................................... 2

CONNECTING THE SERIAL I/O DEVICE (COM1)

...................................................................................... 2

CONNECTING THE CONTROL I/O

.............................................................................................................. 3

CONNECTING THE RS-232 PORT (COM2)

................................................................................................ 3

CONNECTING THE OPTIONAL WLAN (COM2)

......................................................................................... 3

CONNECTING THE OPTIONAL RS-485 (COM2)

....................................................................................... 4

CONNECTING THE OPTIONAL BLUETOOTH (COM2)

............................................................................. 4

CONNECTING THE OPTIONAL ANALOG OUTPUT

.................................................................................. 4

CONNECTING THE POWER SUPPLY

......................................................................................................... 4

CONFIGURATION

.............................................................................................................................................. 5

OVERVIEW

...................................................................................................................................................... 5

ACCESSING THE MENUS

............................................................................................................................. 5

MENU STRUCTURE

....................................................................................................................................... 6

SETUP MENU DESCRIPTIONS

.................................................................................................................... 7

SETUP MENU PROCEDURES

.................................................................................................................... 10

USER MENU DESCRIPTIONS

.................................................................................................................... 11

USER MENU PROCEDURES

...................................................................................................................... 13

BATCH MENU DESCRIPTIONS

.................................................................................................................. 15

BATCH MENU PROCEDURES

................................................................................................................... 15

EXITING THE MENUS

.................................................................................................................................. 16

CALIBRATION ................................................................................................................................................... 17

CALIBRATION OVERVIEW

......................................................................................................................... 17

ZERO CALIBRATION (F16)

......................................................................................................................... 17

SPAN CALIBRATION (F17)

......................................................................................................................... 17

VIEW CALIBRATION VALUES (F18)

......................................................................................................... 18

KEY-IN ZERO CALIBRATION VALUE (F19)

............................................................................................. 19

KEY-IN SPAN CALIBRATION VALUE (F20)

............................................................................................. 19

DISPLAY

........................................................................................................................................................ 20

KEYBOARD

................................................................................................................................................... 21

FUNCTION KEYS

...................................................................................................................................... 21

NUMERIC KEYS

........................................................................................................................................ 22

GENERAL SCALE OPERATION

................................................................................................................ 22

WEIGHING AN ITEM

................................................................................................................................. 22

ENTERING A KNOWN TARE WEIGHT

.................................................................................................. 23

CLEARING A TARE WEIGHT

.................................................................................................................. 23

ENTERING AN ID NUMBER

.................................................................................................................... 23

PROGRAMMING SET POINTS

............................................................................................................... 23

PROGRAMMING OVER/UNDER VALUES

............................................................................................ 24

ADVANCED SCALE OPERATION

.............................................................................................................. 25

APPLICATION (F30) SUMMARY

............................................................................................................ 25

STANDARD OUTPUTS

............................................................................................................................ 26

ACCUMULATION APPLICATION (F30 = 1)

........................................................................................... 26

REMOTE DISPLAY APPLICATION (F30 = 2)

........................................................................................ 26

PIECE COUNT APPLICATION (F30 = 3)

................................................................................................ 26

PERCENTAGE APPLICATION (F30 = 4)

............................................................................................... 27

HOLD APPLICATION (F30 = 5)

............................................................................................................... 28

CHECKWEIGHING APPLICATION (F30 = 6)

........................................................................................ 28

BATCHING APPLICATION (F30 = 7)

..................................................................................................... 29

TRUCK WEIGH IN/WEIGH OUT APPLICATION (F30 = 8)

................................................................... 30

LEGAL FOR TRADE SEALING

...................................................................................................................... 31

Summary of Contents for TI-1680
















































Search results

Summary of Contents for TI-1680

Reviews:

Related manuals for TI-1680

Brands by name

Popular brands

Transcell Technology TI-1680, Setup And Operation Manual

Search results

Summary of Contents for TI-1680

Reviews:

Related manuals for TI-1680

Brands by name

Popular brands