background image

   MS-SVX10A-EN

  25

Installation Indoor Unit

Extra Part 3
Extra Part 2
Extra Part 1

Fitting
pipe for
gas side

Power
connection
cord

Fitting pipe
for liquid
side

Drain
pipe

Heat
Insulation

Wrapping
tape

Figure 9

Installing Indoor Unit

Fitting pipe can come four directions, that is, right,
rear right, left and rear left.

1.  When laying the pipe line on either the left or right

side, cut out extra part as needed to accommodate
piping at the tube exit plate on the base of the unit.
See Figure 9.

         (1) When only drawing out the power line, cut
               Extra Part 1.
         (2) When drawing out the connecting pipe
               and the electric line, cut Extra Parts 1 and
               2 (or 1, 2, 3).

2.  Pull out the fitting pipe from bottom case. Use

adhesive tape to bind the fitting pipe, electric
cable and drain hose and then pass them
through the fitting pipe hole.  See Figure 10.

3.  Hang the brackets at the rear side of the indoor

unit to the hooks on the wall-mounting frame.
Shift the unit left and right to verify that it is
steady. See Figure 11.

4. The installation height of the indoor unit must be

at least 2.0 m.

Figure 10

Left

Left Rear

Right Rear

Right

Figure 11

Support
Hook

Mounting
Plate

Mounting
Plate

Summary of Contents for TXK































Reviews: