background image

8

TTA-R410A

Refrigerant Piping Guidelines

Refrigerant Piping Procedures
(Outdoor units)

Each TTA unit ships with dry nitrogen 
holding charge. Due to this minimal 
amount, we recommend that it be 
removed and the entire system 
evacuated (at the proper time) to avoid 
possible contamination. 
1. Remove the compressor service

access panel.

2. Locate the liquid and suction line

service valves. Check that the
piping connection stubs on the
valves (Figure 1) line up properly
with the holes in the unit cabinet.

3. Front-seat (close) both of the

service valves must be closed
before the system is opened.

suction line service valves before
puncturing the seal caps on the
connection stubs. If the seal caps are
punctured with the valves open, the
refrigerant contained in each circuit
will be lost.

unless they have been punctured. If
caps are intact, application of heat
may generate excessive pressure in
the connection stub, causing personal
injury or death due to rupturing of
components and damage to the
service valve.

4. Heat and remove the seal caps.

caps from refrigerant connections
unit prepared to braze refrigerant
lines to the connections. Excessive
exposure  to atmosphere may allow
moisture or dirt to contaminate the
system, damaging valve seats and
causing ice formation in system
components.

5.

*\[Ä[HUKIYHaL[\IPUNZ[HY[PUN

at the outdoor unit and work toward
the indoor unit.

Note:

 Use long radius ells for all 90

degree bends.

Caution:

 Fully close the liquid and

Warning:

 Do not heat the seal caps

Caution:

 Do not remove the seal

!

!

!

All brazing should be done using 2

[VWZPNKY`UP[YVNLUW\YNLÅV^PUN

through the pipe being brazed 9
(Figure 2).

between the nitrogen source and
the gauge manifold (Figure 2).
Unregulated pressures can damage
system components.

protect painted surfaces from
excessive heat. Heat can damage
system components and the unit

ÄUPZO

6. Shut off nitrogen supply.
7. Shut off  the manifold valve for

the line that is connected to the
suction line service valve.
Disconnect the line from the gauge
port on the value.

Refrigerant Piping Procedure
(Indoor Unit)

Once liquid and suction lines are
complete to the refrigerant
connections on the indoor unit, heat
and remove the seal caps on the
indoor unit connection stubs to
release the dry nitrogen charge.

Caution:

 Install a regulating valve

Caution:

 Wet-wrap all valves and

!

!

1. Remove both seal caps from the

indoor unit connection stubs.

2. Turn nitrogen supply on. Nitrogen

enters through the liquid line
gauge port.

3. Braze the liquid line connections.
4. Open the gauge port on the suction

line and then braze suction line to
the connection stub. Nitrogen will
bleed out the open gauge port on
the suction line.

5. Shut off nitrogen supply.

Leak Check

After the brazing operation of
refrigerant lines to both the outdoor

HUKPUKVVY\UP[PZJVTWSL[LK[OLÄLSK

brazed connections must be checked
for leaks. Pressurize the system
through the service valve with dry
nitrogen to 400 psi. Use soap bubbles
or other leak-checking methods to

LUZ\YL[OH[HSSÄLSKQVPU[ZHYLSLHRMYLL

If not, release pressure, repair and
repeat leak test.

Caution:

 Do not remove seal caps 

until prepared to braze refrigerant lines 
to the connections. Extended exposure 
to atmosphere may allow moisture or 
dirt to contaminate the system, 
damaging system components.

!

Figure 2

Manifold

Gauge

Pressure

Regulating

Valve

Dry

Supply

Nitrogen

Liquid Line

Gauge Port

Liquid Line Service Valve
Note: Detail Service valve  see Fig.1

Suction Line Service Valve
Note: Detail Service valve  see Fig.1

Suction Line Gauge Port

Summary of Contents for ODYSSEY TTA 051 JDF





























Reviews: