Trane BAYEACC25BK1B Installer'S Manual Download Page 10

Page: 10 / 12

Page 10

INSTALLER'S GUIDE

STEP 9

Connect low voltage wiring.

STEP 10 -

Place Wiring Diagram.

1. Attach the wiring diagram, included in the documentation

packet, to the back of the heater compartment panel.

Close up with other wires not shown

STEP

Replace Heater compartment panel on air

handler.

Resistor

Assembly

Low

Voltage

Harness

Electric

Heat Control

Harness

Heater

Resistance

Harness

1. Connect the 4-pin low voltage harness to Electric Heat

Control as shown.

2. If installing in TAMX Air Handler models, connect the 2-pin

resistor ID assembly (tie wrapped to Electric Heat Controls
harness) into the 2-pin heater ID harness as shown.

3. All other Air Handler models, the 2-pin resistor ID assembly

is not used and should be left disconnected.

Summary of Contents for BAYEACC25BK1B













Search results

Summary of Contents for BAYEACC25BK1B

Reviews:

Related manuals for BAYEACC25BK1B

Brands by name

Popular brands

Trane BAYEACC25BK1B, Installer'S Manual

Search results

Summary of Contents for BAYEACC25BK1B

Reviews:

Related manuals for BAYEACC25BK1B

Brands by name

Popular brands