manualshive.com logo in svg

Trane 2GN Series, Installer'S Manual, Page: 20 / 32

Share
Download
Trane 2GN Series Installer'S Manual Download Page 20

20 

18-GL07D1-4

2GN SPLIT INSTALLER’S GUIDE

Thermostat Displays
Fault Flash

When using a fault monitor thermostat and SW2-8 is in the 
pulsing “L” position (off), the system monitor will enable a user 
to view the thermostat and count the fault indicator fl ashes to 
determine the lockout condition the unit is experiencing.

When using A/TCONT802 or 803 thermostat and SW2-8 is 
in the pulsing “L” position (off), the system monitor will enable 
the user to view the thermostat and determine the fault. SW2-
8 in the “on” position will send a constant signal to the fault 
indicator in the event of a system lockout condition. The LED 
board on the front of the unit will display all lockouts. 

The following table shows the codes that will be displayed 
when the System Monitor (L) is connected to the F terminal of 
an A / TCON802 or 803 Comfort Control.

A/TCON802 AND 803 THERMOSTATS

THERMOSTAT DISPLAY

LOCKOUT CODE

LOCKOUT DESCRIPTION

2 FLASHES

HIGH PRESSURE FAULT

3 FLASHES

LOW PRESSURE FAULT

4 FLASHES

NOT APPLICABLE

5 FLASHES

WATER FAULT LOW

6 FLASHES

NOT APPLICABLE

7 FLASHES

CONDENSATE FAULT

8 FLASHES

VOLTAGE OUT OF RANGE

9 FLASHES

RPM FAULT

Summary of Contents for 2GN Series

































Reviews:

No comments