background image

22 

18-GL07D1-4

2GN SPLIT INSTALLER’S GUIDE

DIP SWITCH SETTINGS

DIP SWITCH 

NUMBER

DESCRIPTION

OFF POSITION

ON POSITION

SW1

N/A

NOT USED

N/A

N/A

SW2

1

Service/Test Mode - Allows control of “NORM” or “TEST” operational 
modes. Test mode accelerates most timing functions 16 times to allow 
faster troubleshooting. Test mode also allows viewing the “CURRENT” 
status of the fault inputs on the LED display.

TEST

NORM

2

Freeze Detection (Water Flow)

This lockout mode occurs when the freeze detection thermistor 
temperature is at or below the selected point (well 30°F or loop 15°F) for 
30 continuous seconds.

LOOP 

(PROTECTION 15° 

F)

WELL 

(PROTECTION 

30° F)

3

Accessory Relay

Allows fi eld selection of the accessory relay to operate with the 
compressor or fan.

FAN

COMP

4

NOT USED

N/A

N/A

5

NOT USED

N/A

N/A

6

Input Diagnostics - Allows viewing the inputs from the thermostat to the 
control board such as Y1, Y2, O, G, W, SL1-In on the LED display.

DIAGNOSTIC 

INPUTS VIEWED AT 

LEDS

NORMAL 

DISPLAY 

VIEWED AT 

LEDS

7

Output Diagnostics - Allows viewing the outputs from the control board 
such as the compressor, reversing valve, blower, hot water pump, and loop 
pump on the LED display.

DIAGNOSTIC

OUTPUTS VIEWED 

AT LEDS

NORMAL 

DISPLAY 

VIEWED

AT LEDS

8

Thermostat Selection
Confi gures the control for a pulsed lockout signal (ComforTalk and 
FaultFlash thermostats) or continuous 5 VAC lockout signal.

PULSED “L”

SIGNAL

CONTINUOUS 

“L”

SIGNAL

SW3

1

Single or Dual Capacity Operation

DUAL CAP

1 SPEED

2

Zoned/Finish on Second Stage

This switch allows the unit to down stage with the thermostat when off and 
fi nish with second stage when on. Finish on second stage reduces stage 
changing in reciprocating dual capacity compressors.

NORMAL -

ALL OTHER 

SYSTEMS

FINISH ON 

2ND UNZONED 

DUAL 

CAPACITY

E-SERIES OR

PREMIER 2 

SPEED

3

ECM Fan Monitoring - Set for No PRM on split systems

NO RPM

RPM

4

NOT USED

N/A

N/A

5

On dual capacity units this switch allows stage change: on the fl y when off, 
and 1 minute delay when on. A delay is required on all reciprocating dual 
capacity units.

TAMG SERIES

N/A

Summary of Contents for 2GN Series

































Reviews: