Trailboss QTHN454L Fitting Instructions Manual Download Page 11

Page: 11 / 12

Wiring Loom Fitting Instructions

To Suit Honda CR-V

Part Number 101866-WL

Page

3 of 3

Issue Date

15-02-18

Cequent Customer Service

Ph: 1800 812 017 Fax: 03 9797 3299

Email: [email protected]

Post: PO Box 4050, Dandenong South VIC 3175

Note: Ensure ECU connector is facing down.

24. Connect the trailer wiring ground ring terminal to the vehicle grounding point.

25. Continue routing the trailer harness toward the front of the vehicle.

26. Route the Trailer Wiring Harness along the lower RHS interior of the vehicle, following
existing wiring where possible.

27. Under the vehicle dash, locate the 22-way green connector above the fuse panel.

28. Disconnect it and connect the vehicle T-Patch in between.

29. Remove the indicated 20A fuse (1) and discard.

30. Insert the two supplied fuses into the Add-A-Fuse Adapter.

31. Insert the Add-A-Fuse Adapter into the previously removed fuse location.

Note: Ensure lead is pointing down.

32. Connect the trailer wiring harness to the Add-A-Fuse.

33. At the rear of the vehicle, secure the 7-pin Socket from the tail (400mm) to the towbar.

34. Route the tail harness up and across to the mating blue connector on the trailer wiring

harness.

35. Connect the tail harness 8-way connector to the trailer patch 8-way mating connector.

36. Apply silicone grease to waterproof the connector.

37. Test the trailer wiring harness function using a light board or multi-meter. Secure all

harnesses using cable ties (not supplied).

38. Re-fit all removed parts and secure all fasteners, ensuring there are no squeaks or

rattles.

39. Place the fitting instructions in the glove box after fitment.

Summary of Contents for QTHN454L













Search results

Summary of Contents for QTHN454L

Reviews:

Related manuals for QTHN454L

Brands by name

Popular brands

Trailboss QTHN454L, Fitting Instructions Manual

Search results

Summary of Contents for QTHN454L

Reviews:

Related manuals for QTHN454L

Brands by name

Popular brands