Trafox SUPERINTEND IM-01.IND Instructions For Installation And Use Manual Download Page 12 | Manualshive

Page: 12 / 50

Trafox SUPERINTEND IM-01.IND Instructions For Installation And Use Manual Download Page 12

12

© Copyright Muuntosähkö Oy

–

Trafox

Superintend IMD

http://www.trafox.fi

HW SETTINGS OF THE IM-01.IND UNIT

Setting a device address is not necessary in the IM-01.IND unit. If the IM-01.IND unit is
at the end of the bus, a terminator must be connected. The terminator jumper is
located under the centre cover in the location indicated in the Figure. Open the cover by
using a small screwdriver between the cover and the case to pry the cover loose.

HW SETTINGS OF THE CLT-01 UNIT

Setting a device address is not necessary in the CLT-01 unit. If the CLT-01 unit is at the
end of the bus, a terminator must be connected by changing the location of the
terminator jumper to the left and middle pins. The terminal jumper is under the
connector cover, above the terminal strip, as shown in the Figure. Open the cover by
using a small screwdriver between the cover and the case to pry the cover loose.

To open the cover: pry the cover loose with a screwdriver here and remove the cover

Terminator jumper

To open the cover: pry the cover loose with a screwdriver here and remove the cover

Terminal jumper not
connected

Terminal jumper
connected

«
...
10
11
12
13
14
...
»

Summary of Contents for SUPERINTEND IM-01.IND



















































Reviews:

No comments