Tractor Supply M150 Owner'S/Operator'S Manual Download

Page: 53 / 102

Crossing Streams
Your ATV can operate through water up to maximum
recommended depths is 4 inch

（

100mm

）

. Before fording

steams always:

1. Determine water depths and current.
2. Choose a crossing where both banks have gradual inclines.
3. Proceed slowly, avoiding rocks and obstacles if possible.
4. After crossing, dry the brakes by applying light pressure to the

lever until braking action is normal.

CAUTION

Never operating the ATV through deep or fast flowing water.

NOTE:

After running the vehicle in water, it is critical your

machine is serviced as outlined in the maintenance chart see

“15.maintenance”

.The following areas need special attention:

engine oil, transmission oil and all grease fittings.

11. RIDING

Summary of Contents for M150







































































































Search results

Summary of Contents for M150

Reviews:

Related manuals for M150

Brands by name

Popular brands

Tractor Supply M150, Owner'S/Operator'S Manual

Search results

Summary of Contents for M150

Reviews:

Related manuals for M150

Brands by name

Popular brands