background image

5353-M1-001-EN-02 

 

6.

 

Status beeps:

 

BSU beeps repeat every 4 seconds. 
Light load detected 

2 beeps 

Battery error (high impedance) 

3 beeps - Check connections and battery. 

Connection Error 

4 beeps - Check connections. 

 
SSU beeps repeat every 15 minutes. 
Battery error (low voltage) 

2 beeps - Check connections and battery. 

Battery error (high impedance) 

3 beeps 

 Check connections and battery. 

Connection Error 

4 beeps 

 Check connections. 

 

 

7.

 

Symbols 
 

The following symbols appear on the battery support units: 
 

O/I

  

 
AC Power - 

Illuminated when supply is reaching unit 

+  

     +

 

 
Polarity -   

Green when good 

 

 

Red when reversed 

 
 

 

 
Output -   

Illuminated when output is active 

 

8.

 

Warranty and Service

 

 
For technical support call 866-628-5508  
or email [email protected] 
 
For repair service, go to  

repairtrack.bosch-automotive.com

  

or call 800-344-4013 
 

9.

 

Manufacturer Information

 

 
Traction products are manufactured by: 
Traction Chargers 
Roundway Hill Business Centre 
Devizes 
Wiltshire 
SN10 2LT UK 
 
+44(0)330 022 7822 

[email protected]

 

 
 
 
 

 

Summary of Contents for BSU2-50







Reviews: