Tractel PKR1600D Assembly And Operating Manual Download Page 40

Page: 40 / 40

Tractel

Tractel® Ltd.

Griphoist Division

11020 Mirabeau

Anjou, Quebec H1J 2S3

Toll Free 1-800-561-3229

Tel: (514) 493-3332

Fax: (514) 493-3342

As we are dedicated to continuous improvement of our products, the TRACTEL

reserves the right to modify

the specifications of the equipment described in this manual. As a result, illustrations may not represent

exactly the product you receive: components and/or design may differ.

The companies of the TRACTEL

and their agents or distributors will supply on request descriptive

documentation on the full range of TRACTEL

products: lifting and pulling machines, permanent and

temporary access equipment, safety devices, electronic load indicators, accessories such as blocks, hooks,

slings, ground anchors, etc.

Distributed By:

2016

Tractel

Version

T4766ONT

-GCD-100-

12/16

All

rights

reserved.

Summary of Contents for PKR1600D






































Search results

Summary of Contents for PKR1600D

Reviews:

Related manuals for PKR1600D

Brands by name

Popular brands

Tractel PKR1600D, Assembly And Operating Manual

Search results

Summary of Contents for PKR1600D

Reviews:

Related manuals for PKR1600D

Brands by name

Popular brands