manualshive.com logo in svg

Tracmaster Camon SG30, Original Instruction Manual

Share
Download
Tracmaster Camon SG30 Original Instruction Manual Download Page 5

CAMON SG30 Stump Grinder

SG30 Stump Grinder

 

Page 3

2.0  What the Machine is Designed For

2.1 

Applications

The CAMON SG30 Stump Grinder has been designed by Tracmaster for removing 

tree stumps from above and below the surface of the ground.
The benefit of removing a tree stump is that it allows the landscape to be redesigned 

without the stump.
The teeth of the CAMON SG30 Grinder are designed to grind TREE STUMPS ONLY 

- they are NOT designed to make contact with solid ground at any point during 

operation.
The  machine  will  be  damaged  should  the  teeth  continuously  come  into  contact 

with solid ground.
DO  NOT  use  the  CAMON  SG30  Grinder  for  cutting  grass  or  digging  the  ground. 

These operations will result in damage to the machine.
Operating the machine on non-grass surfaces such as concrete or tarmac will cause 

damage to the SG30 Grinder.
DO NOT use the Stump Grinder if there is a likelihood of high temperatures.

Summary of Contents for Camon SG30





























Reviews:

No comments

Brands by name

Popular brands

Load more brands