manualshive.com logo in svg

TPS WP-81, Manual, Page: 8 / 51

Share
Download
TPS WP-81 Manual Download Page 8

 

Page 8 

1.3  Specifications 

Conductivity 
Ranges ............................. 4 ranges, with automatic range selection. 

k=0.1 Sensor ... 0 uS/cm to 2000  uS/cm 
k=1.0 Sensor ... 0 uS/cm to 20.00 mS/cm 
k=10  Sensor ... 0 uS/cm to 200.0

.

mS/cm 

Resolution ......................... 0.05% of selected range 
Accuracy ........................... 

0.5% of full scale of selected range at 25 

O

C 

TDS 
Factor: .............................. 0.40 to 1.00 - user set (factory default 0.65) 
Ranges: ............................ 4 ranges, with automatic range selection. 

k=0.1 Sensor ... 0 ppM to 1000 ppM 
k=1.0 Sensor ... 0 ppM to 10.00 ppK 
k=10  Sensor ... 0 ppM to 100.0

.

 ppK 

Resolution ......................... 0.1% of selected range 
Accuracy ........................... 

0.5% of full scale of selected range at 25 

O

C 

Salinity .............................. k=0.1 Sensor  0 %  

to 0.10 % 

0 PSU to 1.0   PSU 

k=1.0 Sensor ... 0 %  

to 1.19 % 

 

0 PSU to 11.9 PSU 

k=10  Sensor ... 0 %  

to 8.00 % 

 

0 PSU to 80.0 PSU 

Resolution ......................... 0.01% / 0.1 PSU 
Accuracy ........................... 

0.5% of full scale of selected range at 25 

O

C 

pH 
Range ............................... 0 to 14.00 pH 
Resolution ......................... 0.01 pH 
Accuracy ........................... 

0.01 pH 

mV/ORP 
Range ............................... 0 to ±500.0 and 0 to ±1500 mV (auto-ranging) 
Resolution ......................... 0.15 and 1 mV 
Accuracy ........................... ±0.3 and ±1 mV 

Temperature 
Range ............................... -10.0 to 120.0 

o

C (Sensor limit 60 

o

C) 

Resolution ......................... 0.1 

o

C 

Accuracy ........................... 

0.2 

o

C 

Summary of Contents for WP-81




















































Reviews:

No comments