manualshive.com logo in svg

TPS WP-81, Manual, Page: 29 / 51

Share
Download
TPS WP-81 Manual Download Page 29

 

Page 29 

11.5  Commands 

The following commands can be sent from a PC to the 

WP-81

. Note that 

<cr> denotes carriage return and <lf> denotes a line feed. 

Action 

Command  Notes 

Request current 
data 

?D<cr> 

Returns  the  current  Conductivity/ 
TDS/Salinity, pH, Temperature, date 
and  time  from  the 

WP-81

.  The  log 

number returned is set to Zero. 

Request logged data  ?R<cr> 

Returns  all  logged  records from the 

WP-81

 memory. The data ends with 

the message 

ENDS

<cr> 

Erase logged data 

?E<cr> 

Erases  all  logged  records  from  the  

WP-81

 

memory. 

Returns 

the 

message 

ERASED

<cr>  to  confirm 

that the records have been erased. 

Request status 
information 

?S<cr> 

Returns  the  model  name,  firmware 
version  number,  instrument  serial 
number  and  number  of  logged 
readings in memory, 
eg: 

WP81



V1.0

S1234

9999

<cr>, 

where 

  are  spaces.  Note  that  the 

number  of  logged  readings  is  right-
justified. 

Request GLP 
information 

?G<cr> 

Returns all calibration GLP 
information, plus the instrument 
model and current date (see section 
11.6 for data format and 
handshaking). 

Summary of Contents for WP-81




















































Reviews:

No comments