manualshive.com logo in svg

TPS WP-81, Manual, Page: 30 / 51

Share
Download
TPS WP-81 Manual Download Page 30

 

Page 30 

11.6  Data Format 

Data is returned to the RS232 Port by the 

WP-81

 in the following format. 

Please  note  that  a  “ 

 

”  shown  anywhere  in  this  section  denotes  one 

space.

 

LLLL

CCCCCCccc

PPPPPPppp

TTTTTTttt

dd/mm/yy

hh:mm:ss

 

where… 

LLLL

 

is the Log Number. Maximum 4 characters, right justified. 

The 

WP-81

 sends Zero for instant readings (section 11.2) 

CCCCCC

 

is  the  Conductivity,  TDS  or  Salinity  Data.  Maximum  6 
characters, right justified. 

ccc

 

is 

the  unit  description,  either  “

uS

”,  “

mS

”,  “

ppM

”,  “

ppK

”, 

“%



“ or “psu”. 

PPPPPP

 

is  the  pH  or  ORP/mV  Data.  Maximum  6  characters,  right 
justified. 

ppp

 

is the unit description, sent as “

pH

” or “

mV

” 

TTTTTT

 

is  the  Temperature  Data.  Maximum  6  characters,  right 
justified. 

ttt

 

is  the  Temperature  unit  description.  The 

WP-81

  sends 

“

oC

”  for  real  temperature  data,  or  “

oCm

”  when  manual 

temperature compensation is being used. 

dd/mm/yy

 

is the date, month and year data. 

hh:mm:ss

 

is the hours, minutes and seconds data. 

Notes 

1.  When  requested  by  a  PC  with  the  ?D  or  ?R  commands  (section 

11.5), the data is terminated with a carriage return. 

2.  When the data is sent by the 

WP-81

 using the Print function (section 

9.4) or the Instant Send function (section 11.2), the data ends with a 
carriage return and a line feed. 

3.  When  the  Temperature  is  not  within  the  ATC  limits  for 

Conductivity/TDS/Salinity or pH measurement “ATCLIM” will be sent 
instead of the Data. 

Summary of Contents for WP-81




















































Reviews:

No comments