TPS Aqua-D Manual Download Page 6 | Manualshive

Page: 6 / 28

TPS Aqua-D Manual Download Page 6

Page 5

1.2.2 Aqua-DY

Standard Kit includes…

Part No

1.

Aqua-DY

Dissolved Oxygen-Temperature Instrument........... 123144

2. 9V Battery ............................................................................. 130026

3.

Aqua-D

Handbook ................................................................ 130050

Sensor and cables…

1. YSI Field Dissolved Oxygen sensor, (no cable) ..................... 123204

(includes integral protector and membrane kit)

2. 1m detachable cable for YSI Dissolved Oxygen sensor......... 123212

3. 3m detachable cable for YSI Dissolved Oxygen sensor......... 123221

4. 5m detachable cable for YSI Dissolved Oxygen sensor......... 123222

5. Extended cable (ordered by the metre).................................. 130040

6. YSI non-stirring BOD bottle sensor........................................ 123214

7. YSI self-stirring BOD bottle sensor ........................................ 123213

Options that may have been ordered with your Aqua-DY:

1. Hard Plastic Carry Case ........................................................ 130057

Other spares:

1. Membrane kit ........................................................................ 123300

(includes Filling Solution, Sodium Sulphite, 2 Membrane Envelopes
and 2 O-Rings)

2. Filling Solution, 45mL ............................................................ 123303

3. Sodium Sulphite for Zero Calibration, 50g ............................. 123302

«
...
4
5
6
7
8
...
»

Summary of Contents for Aqua-D





























Reviews:

No comments