manualshive.com logo in svg

TPS Aqua-D, Manual, Page: 18 / 28

Share
Download
TPS Aqua-D Manual Download Page 18

Page 17

7. Initialising the Aqua-D

If the calibration settings of the 

Aqua-D

 exceed the allowable limits, and

the unit cannot be re-calibrated, then it may need to be initialised to
factory default values. This action may be required if a sensor is replaced.

To initialise the 

Aqua-D

…

1. Switch the 

Aqua-D

 off.

2. Press AND HOLD the 

 key while switching the 

Aqua-D

 on.

3. The following messages are now displayed…

Memory & Cal
Reset !

↓↓

You MUST
Re-Calibrate

↓↓

TPS AQUA-D
V1.0  S1234

4. The meter then displays % Saturation and Temperature. Note that

the decimal points have been replaced with a “ 

∗

 “, to indicate that the

unit requires re-calibration.

8. Instrument software version number.

If you need to phone or fax TPS for any further technical assistance, the
version number of your 

Aqua-D

 firmware may of benefit to us. Please

obtain the version number before phoning or faxing.

The version number is displayed on the bottom left of the display when
the 

Aqua-D

 is switched on. For example…

TPS AQUA-D
V1.0  S1234

“

V1.0

” in this example is the firmware version number.

“

S1234

” in this example is the instrument’s serial number.

Summary of Contents for Aqua-D





























Reviews:

No comments