TPS Aqua-D Manual Download Page 5 | Manualshive

Page: 5 / 28

TPS Aqua-D Manual Download Page 5

Page 4

1.2 Unpacking Information

Before using your new

Aqua-D

, please check that the following

accessories have been included:

1.2.1 Aqua-D

Standard Kit includes…

Part No

1.

Aqua-D

Dissolved Oxygen-Temperature Instrument ............. 123143

2. 9V Battery ............................................................................. 130026

3.

Aqua-D

Handbook ................................................................ 130050

Sensor and cables…

1. ED1 Dissolved Oxygen sensor, (no cable) ............................ 123400

(includes sensor protector and membrane kit)

2. 1m detachable cable for ED1 Dissolved Oxygen sensor ....... 123228

3. 3m detachable cable for ED1 Dissolved Oxygen sensor ....... 123230

4. 5m detachable cable for ED1 Dissolved Oxygen sensor ....... 123232

5. Extended cable (ordered by the metre).................................. 130040

Options that may have been ordered with your Aqua-D:

1. Hard Plastic Carry Case ........................................................ 130057

2. Adaptor to fit sensor into standard BOD bottle....................... 123201

Other spares:

1. Membrane kit ........................................................................ 123301

(includes Filling Solution, Sodium Sulphite and Membrane Sheet)

2. Filling Solution, 45mL ............................................................ 123303

3. Sodium Sulphite for Zero Calibration, 50g ............................. 123302

«
...
3
4
5
6
7
...
»

Summary of Contents for Aqua-D





























Reviews:

No comments