Toyotomi Laser Clean LC-41 Instruction Manual Download Page 6

5

SET CLOCK

It is only possible to set the correct time, when the heater is

connected to the mains and not burning.

1.  Use the Adjustment Keys (

hour /

min.) to set the time.

2.  To set the time, press “hour” and “min.”

set buttons. Individual motions will

increase the time by one unit; holding

continuously will raise either the “hour” or

“min.” rapidly. After approximately 10

seconds the blinking will stop and the

setting will be locked. 5 Minutes after

switching off the heater, the information on the display will disappear and the heater

will automatically switch into the stand-by position.

1.  Just press the

button to ignite the

heater. The 

button will start blinking,

indicating that the ignition procedure has

started. This will take a short while.

2.  After this time heater will automatically

ignite and The button will cease its flashing. The Operation Lamp will remain alight

so long as heater is burning.

NOTE: If using your heater for the first time, or after long term storage, ignition may

not take place on the first try. Press the

button again.

NOTE: Fuel pump may produce an audible operating noise at ignition. This is only

temporary.

IGNITION

1

2

OPERATION

CAUTION : Always make sure that there is sufficient ventilation.

 LC-41  10.7.21 2:48 PM  ページ 5

Summary of Contents for Laser Clean LC-41
















Reviews: