manualshive.com logo in svg

Toyota PRUS V 2020, Owner'S Manual

Share
Download
Toyota PRUS V 2020 Owner'S Manual Download Page 406

404

7-2. Steps to take in an emergency

PRIUS v_OM_OM47D92E_(AE)

Turn the compressor switch  on
and wait for an approximately 5
seconds,  and  then  turn  it  off.
Check  the  tire  inflation  pres-
sure.

If the tire inflation pressure is
under  130  kPa  (1.3  kgf/cm

2

or bar, 19 psi): The puncture
cannot  be  repaired.  Contact
your Toyota dealer.
If the tire inflation pressure is 130 kPa (1.3 kgf/cm

2

 or bar, 19 psi)

or  higher,  but  less  than  the  specified  air  pressure:  Proceed  to
step 

.

If the tire inflation pressure is the specified air pressure (

P. 434):

Proceed to step 

.

Turn the compressor switch on to inflate the tire until the specified
air  pressure  is  reached.  Drive  for  about  5  km  (3  miles)  and  then
perform step 

.

Attach the air release cap to the
end of the hose.

If  the  air  release  cap  is  not
attached, the sealant may leak and
the vehicle may get dirty.

Store the bottle in the luggage compartment while it is connected to
the compressor.
Taking  precautions  to  avoid  sudden  braking,  sudden  acceleration
and sharp turns, drive carefully at under 80 km/h (50 mph) to the
nearest Toyota dealer for tire repair or replacement.

21

1

2

22

3

23

22

20

23

24

25

Summary of Contents for PRUS V 2020




















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands