manualshive.com logo in svg

Toyota LANDCRUISER PZQ8460320, Fitting Instructions Manual

Share
Download
Toyota LANDCRUISER PZQ8460320 Fitting Instructions Manual Download Page 27

© Toyota Motor Corporation Australia Ltd. 2011. All rights reserved. 

REPAIR MANUAL REFERENCE 

LANDCRUISER -  Steel S/Cab Tray Body 

ISSUE:  27/07/2012 

Page 

Refer to ServiceNet 

Accessory Part No.: PZQ8460320 

Fitting Instr. Part No.: PZQ8460320-FI 

27 of 35 

NOTE: - 

Headboard Tyre Hanger Option 

 STEP 

  

52 

NOTE: -  

Under Body Tyre Hanger Option 

 STEP 

  

53 

Note: 

Following steps are for Under Body Tyre Hang-

er option only.   
 
Assemble the registration plate to the registration light 
assembly bracket using M6x16 Bolts and M6 Nyloc 
Nuts as shown in adjacent diagram.     

Registration Plate 

M6x16 Bolts 

Registration Light 
Assembly Bracket 

Registration Light  

M6 Nyloc Nut 

NOTE: -  

Under Body Tyre Hanger Option 

 STEP 

  

54 

Assemble the registration light assembly bracket and 
registration plate to the Underbody Tyre Hanger regis-
tration bracket using M8x20 bolts and M8 Nyloc Nut 
as shown in adjacent diagram.   
 
Check the registration plate lamps are aimed directly 
toward the registration plate bracket.  
   

M8x20 Bolt 

Under Body Tyre Hanger  
Registration Bracket 

M8 Nyloc Nut 

There are wiring harnesses attached to each side of 
the chassis. 
Remove the zip ties attaching the two wiring harness-
es. Remove the caps from the wiring plugs. 
Ensure any spare plugs have caps fitted. 
Using saddle clips and cable ties, route and attach the 
two supplied registration plate lamp wiring patches 
(part no. 2EH04) to the vehicle wiring harness. 
The left hand lamp wiring patch to the LHS of the 
chassis, the right hand lamp wiring patch to the RHS 
of the chassis. 
Using zip ties, re-attach the wiring harness to the 
chassis as shown in the adjacent diagram. 
 

Continue installation from Step 56. 

Wiring patch 

(2EH04) 

FR

Summary of Contents for LANDCRUISER PZQ8460320




































Reviews:

No comments

Brands by name

Popular brands

Load more brands