Toyota GUN120R-BTTLXT3 Body Section Manual Download

Page: 52 / 131

【

】

-6. Brake

- 46 -

6. Brake

CAUTION

The brake system and piping must not be modified.

[1] Readjustment of LSPV

A load sensing proportioning valve (LSPV) is mounted on the base vehicle for stabilizing the brake performance
in accordance with the change of load.

Adjust LSPV after building or alteration (on completion of the vehicle).
Readjustment of a LSPV demounted is always necessary.

(1) LSPV readjustment procedure

①

SST, tools and measuring instruments

SST

09709-29018

Gage set, LSPV

Instrument

Axle load gage

②

Preparation for adjustment

(a) Measure the rear axle load using the axle load gage.

Standard rear axle load for adjustment

Chassis

Body

Models

Rear axle

load [kg]

2WD

Single cab

KUN122R-BPMLYP3

750

Summary of Contents for GUN120R-BTTLXT3




































































































































Search results

Summary of Contents for GUN120R-BTTLXT3

Reviews:

Related manuals for GUN120R-BTTLXT3

Brands by name

Popular brands

Toyota GUN120R-BTTLXT3, Body Section Manual

Search results

Summary of Contents for GUN120R-BTTLXT3

Reviews:

Related manuals for GUN120R-BTTLXT3

Brands by name

Popular brands