background image

INTRODUCTION

MAIN COMpONENTS

TOOLS AND  

pREpARATION

MEASUREMENT

LASER bEAM  

AxIS ADJUSTMENT

 

UppER/LOWER SIDE (A)

    Between 2.7° and 0°

 

RIGHT/LEFT SIDE (b)

 

  Between 4.0° and 0°

Tip

Click

Help

Tip

Help

Click

Note

Note

Tip

Click

Help

Tip

Help

Click

Note

Note

Tip

Click

Help

Tip

Help

Click

Note

Note

Tip

Click

Help

Tip

Help

Click

Note

Note

Tip

Click

Help

Tip

Help

Click

Note

Note

Tip

Click

Help

Tip

Help

Click

Note

Note

STE

p

 12 E

x

AM
p

LE

SENSOR ADJUSTMENT

ADJUSTMENT 

p

ROCEDURE

12.

  When the Laser Cruise Divergence Data values are within the STANDARD 

VALUES FOR DIVERGENCE, check for a laser beam signal between the Laser 

Sensor and the reflector SST by moving the SST: 

 

a. 100mm to the 

left

 of Point G

    b. 100mm to the 

right

 of Point G

  If the “UPPER/LOWER SIDE” and “LEFT/RIGHT SIDE” values change 

 

when moving the reflector SST to the left and right, a laser beam signal 

is being sent by the sensor emitter and then reflected back to the sensor 

receiver by the SST.

13.

  Now return the reflector SST to Point G and make sure that the values are still 

within the Standard Values for Divergence.

Now that the sensor is within the Standard Values for Divergence, make 

sure to perform Steps 14 and 15 to store the adjustment data in the Laser 

Radar Cruise ECU and to complete the adjustment procedure.

STORING THE ADJUSTMENT DATA IN THE LASER RADAR CRUISE ECU
14.

  Turn the headlight switch from OFF to the TAIL position and observe the 

LASER CRUISE DIVERGENCE DATA screen on Techstream.

The adjustment is completed when:

•  UPPER/LOWER SIDE and RIGHT/LEFT SIDE readings show 

 

“0” and the system beeps for 10 seconds

•  UPPER/LOWER SIDE and RIGHT/LEFT SIDE alternately 

 

flash on the screen

15.  

Select 

NExT

 on Techstream to store

 the adjustment data in the Laser Radar 

Cruise ECU and complete the procedure.

If NExT is not selected, the adjustment data will not be stored.

DYNAMIC LASER CRUISE CONTROL SYSTEM 2008 - 2012 SEQUOIA

Quick Training Guide – QT512A

Before beginning the beam axis adjustment procedure, make sure that the:

•  Headlight switch is in the OFF position.
•  Reflector SST is accurately placed on Point G.

1.

 Connect Techstream to DLC3, then turn power ON.

2

. Turn the ignition switch to ON.

3

. Start the Techstream program.

4.

  Select Connect to Vehicle.

5.

 From the Option pull-down, select LASER CRUISE and click Next.

6.

  Push the Cruise Control Main switch to ON.

7.

  From the System Select menu, select Laser Cruise and click the Next arrow.

8.

  From the Laser Cruise Live tab, select Utility.

9.

  Select Beam Axis Adjustment and click the Next arrow.

10

. From the Beam Axis Adjustment pop-up, click next.

11.  

Check that the Laser Cruise Divergence Data on Techstream is within the 

Standard Values of Divergence*.

If the Laser Cruise Divergence Data does not meet the Standard Values of 

Divergence, adjust the laser sensor by using the 

Mechanical Adjustment 

Method

 under the SENSOR ADJUSTMENT tab before continuing with Step 12.

Laser beam Axis Adjustment procedure

STANDARD VALUES FOR DIVERGENCE

Click all side tabs

©Toyota Motor Sales, U.S.A., Inc., 2012

Summary of Contents for Dynamic Laser Cruise Control System























Reviews: