Toyota Corolla 2008 Owner'S Manual Download Page 275

Page: 275 / 310

’08 Corolla_U (L/O 0706)

277

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

NOTICE

Be sure the engine and all accesso-
ries are off before performing main-
tenance.

When checking the battery, remove
the ground cable from the negative
terminal (“−” mark) first and rein-
stall it last.

Be careful not to cause a short cir-
cuit with tools.

Take care no solution gets into the
battery when washing it.

Type A

Green

Dark

Clear or
light yellow

Type B

Blue

White

Red

CHECKING BY INDICATOR

Check the battery condition by the indi-
cator color.

Indicator color

Condition

Type A

Type B

Condition

Green

Blue

Good

Dark

White

Charging necessary.
Have battery
checked by your
Toyota dealer.

Clear or

light

yellow

Red

Have battery
checked by your
Toyota dealer.

During recharging, the battery is pro-
ducing hydrogen gas.

Therefore, before recharging:

1. If recharging with the battery installed

on the vehicle, be sure to disconnect
the ground cable.

2. Be sure the power switch on the re-

charger is off when connecting the
charger cables to the battery and when
disconnecting them.

CAUTION

Always charge the battery in an un-
confined area. Do not charge the
battery in a garage or closed room
where there is not sufficient ventila-
tion.

Only do a slow charge (5 A or
less). Charging at a quicker rate is
dangerous. The battery may ex-
plode, causing personal injuries.

NOTICE

Never recharge the battery while the
engine is running. Also, be sure all
accessories are turned off.

—Checking battery condition

Battery recharging precautions

Summary of Contents for Corolla 2008























































































































































































































































































































Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands

Toyota Corolla 2008, Owner'S Manual

Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands