manualshive.com logo in svg

Toyota CAMRY HYBRID 2021, Owner'S Manual

Share
Download
Toyota CAMRY HYBRID 2021 Owner'S Manual Download Page 536

534

7-2. Steps to take in an emergency

CAMRY_HV_GE

■

If “Auto Power Off to Conserve Battery” is displayed

This message is displayed when the power was cut off due to the automatic
power off function.
The next time the hybrid system is started, keep the hybrid system operating
for approximately 5 minutes to recharge the 12-volt battery.

■

If “A New Key has been Registered Contact Your Dealer for Details” is
displayed

This message will be displayed each time the driver’s door is opened when
the doors are unlocked from the outside for approximately one week after a
new electronic key has been registered.
If this message is displayed but you have not had a new electronic key regis-
tered, ask your Toyota dealer to check if an unknown electronic key (other
than those in your possession) has been registered.

■

When “Headlight System Malfunction Visit Your Dealer” is displayed

The following systems may be malfunctioning. Have the vehicle inspected by
your Toyota dealer immediately.

●

The LED headlight system

●

The automatic headlight leveling system (if equipped)

●

AHB (Automatic High Beam) (if equipped)

■

If “Radar Cruise Control Unavailable See Owner's Manual” is shown

The dynamic radar cruise control with full-speed range or dynamic radar
cruise control system is suspended temporarily or until the problem shown in
the message is resolved. (causes and coping methods:



P. 280)

■

If “Radar Cruise Control Unavailable” is shown

The dynamic radar cruise control with full-speed range or dynamic radar
cruise control system cannot be used temporarily. Use the system when it
becomes available again.

■

If a message that indicates the malfunction of front camera is displayed
(if equipped)

The following systems may be suspended until the problem shown in the
message is resolved. (

P. 280, 522)

●

PCS (Pre-Collision System)

●

LTA (Lane Tracing Assist)

●

Dynamic radar cruise control with full-speed range

●

Dynamic radar cruise control

●

AHB (Automatic High Beam)

CAMRY HYBRID_OM_General_OM33F09E

Summary of Contents for CAMRY HYBRID 2021













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands