Toyota A442F Repair Manual Download Page 117

Page: 117 / 143

AT-104

AUTOMATIC TRANSMISSION - COMPONENT PARTS INSTALLATION

(g) Match the spacer hole to the lever calking hollow and

calk the spacer to the lever.

(h) Make sure the manual valve lever shaft turns smoot-

hly.

2. INSTALL TRANSMISSION REAR COVER

Install a new gasket and rear cover with the three
bolts and six screws.

Torque:7.8 N-m (80 kgf cm, 69 in.-lbf)

3. INSTALL CACCUMULATOR PISTON AND SPRING
(a) coat new two 0 —rings with ATF, and install them to

the piston.

(b) Install the spring and accumulator piston into the bore

of the transmission case.

HINT: Piston, spring diameters and spring free length

are shown in the figure.

(1) New gasket

(2) Plate

(3) New gasket

(4) Front clutch accumulator cover

Summary of Contents for A442F
















































































































































Search results

Summary of Contents for A442F

Reviews:

Related manuals for A442F

Brands by name

Popular brands

Toyota A442F, Repair Manual

Search results

Summary of Contents for A442F

Reviews:

Related manuals for A442F

Brands by name

Popular brands