manualshive.com logo in svg

Toyota 2003 MR2 Spyder, Owner'S Manual

The Toyota 2003 MR2 Spyder Owner's Manual is available for free download on our website. This comprehensive manual includes detailed instructions and essential information about your MR2 Spyder, ensuring a smooth and enjoyable ownership experience. Visit manualshive.com today to access the manual and unlock the full potential of your vehicle.

Share
Download
background image

218

2003 MR2 from Aug. ’03 Prod. (OM17511U)

CHAIN INSTALLATION

Install the chains on the rear tires as
tightly as possible. Do not use tire
chains on the front tires. Retighten
chains after driving 0.5—1.0 km
(1/4—1/2 mile).

When installing chains on your tires, care-
fully follow the instructions of the chain
manufacturer.

CAUTION

Do not exceed 50 km/h (30 mph) or
the chain manufacturer’s recom-
mended speed limit, whichever is
lower.

Drive carefully avoiding bumps,
holes, and sharp turns, which may
cause the vehicle to bounce.

Avoid sharp turns or locked–wheel
braking, as use of chains may ad-
versely affect vehicle handling.

When driving with chains installed,
be sure to drive carefully. Slow
down before entering curves to
avoid losing control of the vehicle.
Otherwise an accident may occur.

NOTICE

Do not attempt  to use a tire chain on
the compact spare tire, as it may re-
sult in damage to the vehicle as well
as the tire.

Replacing wheels

WHEN TO REPLACE YOUR WHEELS

If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replaced.

If you fail to replace a damaged wheel,
the tire may slip off the wheel or cause
loss of handling control.

WHEEL SELECTION

When replacing wheels, care should be
taken to ensure that the wheels are re-
placed by ones with the same load ca-
pacity, diameter, rim width, and offset.

Correct replacement wheels are available
at your Toyota dealer.

A wheel of a different size or type may
adversely affect handling, wheel and bear-
ing life, brake cooling, speedometer/odom-
eter calibration, stopping ability, headlight
aim, bumper height, vehicle ground clear-
ance, and tire or snow chain clearance to
the body and chassis.

Replacement with used wheels is not rec-
ommended as they may have been sub-
jected to rough treatment or high mileage
and could fail without warning. Also, bent
wheels which have been straightened may
have structural damage and therefore
should not be used. Never use an inner
tube in a leaking wheel which is designed
for a tubeless tire.

03 07.07

Summary of Contents for 2003 MR2 Spyder































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 MR2 Spyder

Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Brand: Gardigo Pages: 36
PAC SWI-RC Installation Instructions preview
SWI-RC
Brand: PAC Pages: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Brand: PAC Pages: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Brand: PAC Pages: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Brand: PAC Pages: 5
Porsche 911 GT3 - Brochure preview
911 GT3 -
Brand: Porsche Pages: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Brand: Whispbar Pages: 14
Fiat 500 L 2019 User Manual preview
500 L 2019
Brand: Fiat Pages: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Brand: Honda Pages: 6
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Brand: TATA Motors Pages: 136
SAN HIMA SGBR015 Installation Instructions Manual preview
SGBR015
Brand: SAN HIMA Pages: 10
RHOX LGT-381L Installation Instructions Manual preview
LGT-381L
Brand: RHOX Pages: 8
Saab 9000 1985 Service Manual preview
9000 1985
Brand: Saab Pages: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Brand: A-rival Pages: 23
Gator GT700SD User Manual preview
GT700SD
Brand: Gator Pages: 6
F.lli Menabo CROSS 2 Assembly Instructions Manual preview
CROSS 2
Brand: F.lli Menabo Pages: 16
Cadillac XLR-V Specifications preview
XLR-V
Brand: Cadillac Pages: 2
Buick Cascada 2016 Getting To Know Manual preview
Cascada 2016
Brand: Buick Pages: 20

Brands by name

Popular brands

Load more brands