Toyota 2003 MR2 Spyder Owner'S Manual Download Page 112 | Manualshive

Page: 112 / 318

background image

92

2003 MR2 from Aug. ’03 Prod. (OM17511U)

If you stop for more than 90 seconds with
the selector lever in the “S” position with-
out holding down the brake pedal while
the engine is running, a warning buzzer
(long pulse sound) will sound, and the “N”
indicator in the instrument cluster will
flash, and the system will automatically
shift the transmission gear to the neutral
gear position.

If the driver’s door is opened with the
selector lever in the “S” position without
depressing the brake pedal, warning buzz-
er (long pulse sound) will also sound. 10
seconds later, the “N” indicator in the in-
strument cluster will also flash, and the
system will automatically shift the trans-
mission gear to the neutral gear position.

The gear will resume to 1st or 2nd when
the system is operated as follows:

Brake pedal “ON”: The gear position
before the system selected the “N”
position is resumed.

Operate the selector lever to the “+”
direction: Resume to 2nd gear.

Operate the selector lever to the “–”
direction: Resume to 1st gear.

Push upshift switch on the steering
wheel: Resume to 2nd gear.

Push downshift switch on the steering
wheel.: Resume to 1st gear.

“S”

“N”

“S”: Resume to 1st gear.

When starting off again, always confirm
the gear position by the gear position indi-
cator.

CAUTION

Unlike automatic transmission mod-
els, the sequential manual transmis-
sion models do not creep.

When racing the engine, make sure
that the gear position is in the “N”
position by the gear position indica-
tor. In case the accelerator is oper-
ated with the gear in any other
position, the vehicle may move re-
sulting in an unexpected accident.

When you stop the vehicle, hold the
brake pedal down or shift the selec-
tor lever to the “N” position. If the
selector lever is left in the “S”
position without depressing the
brake pedal for more than 90 sec-
onds while stopping, a warning
buzzer (long pulse sound) will
sound, and the “N” position indica-
tor in the instrument cluster will
flash, and the system will automati-
cally shift the transmission gear to
the neutral gear position. If this
happens on a hill, when starting off
the vehicle, the vehicle may move
unexpectedly and cause an acci-
dent.

Do not leave your vehicle unat-
tended while the engine is running.

03 07.07

«
...
110
111
112
113
114
...
»

Summary of Contents for 2003 MR2 Spyder































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 MR2 Spyder

Brand: Falcon Pages: 8

KO PROPO RTF 2002 ESC

Brand: Tamiya Pages: 2

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

Brand: Phonocar Pages: 2

Dodge Challenger SRT8®Challenger SRT8 392 2012

Brand: Dodge Pages: 5

Brand: Edelbrock Pages: 2

Brand: Streetwize Pages: 4

Brand: Prorack Pages: 15

Brand: Yakima Pages: 28

Brand: Jaeger Pages: 11

Brand: ATS Pages: 12

Brand: ideus Pages: 116

Brand: FIRRAK Pages: 12

Brand: Honda Pages: 5

Brand: Alfa Romeo Pages: 268

Brand: Raider Pages: 2

Brand: Jackson Racing Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands