Toyota 00016-00950 Installation Instructions Manual Download Page 8 | Manualshive

Page: 8 / 16

background image

Page 8 of 16

FR-S 2015

XM Satellite Radio

INSTALLATION PROCEDURES; continued

13. Secure the XM antenna cable to the

existing factory harness located in the
driver’s step sill area with (3) cable ties.

14. Continue to route the XM antenna cable,

under the driver’s seat, to the center con-
sole area.

Cable Ties

Southeast Toyota Distributors, LLC

«
...
6
7
8
9
10
...
»

Summary of Contents for 00016-00950

















Reviews:

No comments

Related manuals for 00016-00950

Brand: Caliber Pages: 4

Brand: Caliber Pages: 34

Brand: Yamaha Pages: 137

Brand: Yamaha Pages: 94

Brand: Teac Pages: 124

Brand: ESX Pages: 16

Brand: Trantec Pages: 22

Brand: Navilock Pages: 12

Brand: Farpointe Data Pages: 2

Brand: Spektrum Pages: 16

Brand: HiTV Pages: 28

Brand: AKG Pages: 125

Brand: TECshow Pages: 18

Brand: Pyle Pages: 4

Brand: Planet Audio Pages: 24

Brand: Promag Pages: 7

Brand: Advanced Microwave Products Pages: 2

AUDIO-B PLUS aptX TWS

Brand: Tinysine Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands