Toyota 00016-00950 Installation Instructions Manual Download Page 7 | Manualshive

Page: 7 / 16

background image

Page 7 of 16

FR-S 2015

XM Satellite Radio

INSTALLATION PROCEDURE; continued

11. Continue to route the XM antenna cable

next to the driver’s side back seat, into the
passenger compartment.

12. Route the XM antenna cable to the driver’s

front door step sill area. Secure the XM an-
tenna cable with (2) cable ties.

Cable Ties

Southeast Toyota Distributors, LLC

«
...
5
6
7
8
9
...
»

Summary of Contents for 00016-00950

















Reviews:

No comments

Related manuals for 00016-00950

Brand: Harman Kardon Pages: 2

Brand: Harman Kardon Pages: 44

Brand: Harman Kardon Pages: 176

Brand: Harman Kardon Pages: 3

Brand: PCTV Systems Pages: 2

C-Tech HD 6600 SST

Brand: Clarke-tech Pages: 32

FlashMover 16-in-1 USB2.0

Brand: Microdia Pages: 2

Brand: VDO Pages: 2

Brand: Creative Access Solutions Pages: 4

Language Master LM-1

Brand: Eiki Pages: 16

Brand: tbs electronics Pages: 15

Brand: Barlow Wadley Pages: 11

Wireless A/V Sender 2.4GHz

Brand: Quatech Pages: 8

Brand: Linx Pages: 24

Brand: Harman Kardon Pages: 52

Brand: Denon Professional Pages: 16

Brand: Kensence Pages: 9

Brand: PCB Piezotronics Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands