manualshive.com logo in svg

Town & Country Fireplaces TC54.CE2 Series C, Installation And Operating Instructions Manual

Share
Download
Town & Country Fireplaces TC54.CE2 Series C Installation And Operating Instructions Manual Download Page 2

  Table of Contents

Caution ........................................................................................... 3
Safety ............................................................................................. 3
Massachusetts Rules and Regulations ........................................... 4
Fireplace Dimensions ..................................................................... 5
Minimum Clearances to Combustible Material ............................... 5
Installation Requirements ............................................................... 6
Manufactured (Mobile) Home ......................................................... 6
Window Frame Removal ................................................................. 6
Top Standoffs .................................................................................. 7
Locating The Fireplace ................................................................... 7
Framing and Finishing .................................................................... 8
Steel Stud Framing Kit .................................................................. 10
Hearth Extension .......................................................................... 12
Maestro Control  ........................................................................... 13
– Plumbing and Electrical ............................................................. 13
Gas Supply ................................................................................... 15
Gas Pressure Check ..................................................................... 15
Horizontal Termination Venting  .................................................... 16
(Power Vented) ............................................................................. 16
Vertical Termination Venting ......................................................... 16
Roof Termination Venting Chart .................................................... 17
Vent Terminal Clearance ............................................................... 20
Vent Restrictor Adjustment ........................................................... 21
Firebox Panels Installation ............................................................ 22
Finishing Touch Trim Kit Instructions ............................................. 23
Lighting Instructions ..................................................................... 24
First Fire ........................................................................................ 24
Maestro Control System ............................................................... 25
Remote Control Initial Setup ......................................................... 25
Maestro Control System - Operation ............................................ 26
    

APPENDIX

    Maintenance ............................................................................. 29
    Replacement Parts ................................................................... 30
    Replacement Parts – Maestro Control System ......................... 31
    Wiring Diagram ......................................................................... 32
    Roof Termination Kit   ............................................................... 33
    Vent Pipe Dimensions  .............................................................. 34
    Vent Offset Chart ...................................................................... 34
    Safety Label Location ............................................................... 35

2

TC54.CE2 080211-36

Summary of Contents for TC54.CE2 Series C





































Reviews:

No comments

Brands by name

Popular brands

Load more brands