Town & Country Fireplaces TC42.NG04C Instructions For Use Manual Download Page 14

Page: 14 / 16

NOT SHOWN

*
*

TC42.NG04C 260411-16

ITEM .......DESCRIPTION ............................................PART NO.

#1.......... TRANQUILITY BURNER KIT ............. TC42.NG04C

#2.......... PEBBLE ASSEMBLY ......................... TC42.9499

#3.......... MAIN SUPPLY TUBE .......................... 5019.223

#4.......... PILOT TUBE ...................................... 5019.225

ITEM .......DESCRIPTION ............................................PART NO.

#5.......... PILOT ASSEMBLY, CONVERTIBLE .. TCRP.5005025

#6.......... ORIFICE, NATURAL GAS (#25) ......... 5022.12

#7.......... PROPANE CONVERSION KIT ........... TC42.LPCE01

#8.......... SAND .................................................. TC42.SAND34

(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)

Replacement Parts

#1.... BURNER ASSEMBLY

TRANQUILITY CURB

19 PORT CAST BURNER

ROCK PAN

LINE COVER, LT

TRANQUILITY LEG

FLOOR PAN

TAPPED 1/8-27 NPT

LINE COVER, RT

BURNER INLET TUBE

CURB CLAMP

PEBBLE

ASSEMBLY

MAIN

SUPPLY

TUBE

PILOT

TUBE

PILOT

ASSEMBLY,

CONVERTIBLE

ORIFICE NG #25

TAPERED PLUGS (not shown)

PROPANE CONVERSION KIT

...(not

shown)

SAND (not shown)

#2.... PEBBLE ASSEMBLY

#3.... MAIN SUPPLY TUBE

#4.... PILOT TUBE

#5.... PILOT ASSEMBLY, CONVERTIBLE

#6.... ORIFICE NG #25

#7.... PROPANE CONVERSION KIT

(not shown)

#8.... SAND

(not shown)

KIT CONTENTS:

Summary of Contents for TC42.NG04C

















Search results

Summary of Contents for TC42.NG04C

Reviews:

Related manuals for TC42.NG04C

Brands by name

Popular brands

Town & Country Fireplaces TC42.NG04C, Instructions For Use Manual

Search results

Summary of Contents for TC42.NG04C

Reviews:

Related manuals for TC42.NG04C

Brands by name

Popular brands