manualshive.com logo in svg

Town & Country Fireplaces TC36.CARE3, Installation And Operating Instructions Manual, Page: 26 / 48

Share
Download
Town & Country Fireplaces TC36.CARE3 Installation And Operating Instructions Manual Download Page 26

Roof Vent Terminal:

1.  Place the roof flashing over the vent pipe, secure and seal it to the roof using the 
 

methods and materials appropriate for the type of roof on the building. Shingle roof

 

example shown (Fig  #43).

2.  Place the storm collar down over the vent pipe until it is level. Tighten storm collar for  
 

a snug fit. Apply a thick horizontal ring of mastic around the pipe at top of the storm  

 

collar (Fig #43).

3.  Lower the roof vent terminal cap over the vent pipe and secure in place with screws 

provided (Fig #43). Seal screw heads and joints with caulking to prevent any moisture 
entering the venting system.

VERTICAL TERMINATION CAP
(TCVT.9365)

FLASHING

STORM COLLAR
(TC42.90665)

MASTIC

NOTE:  ADJUSTABLE FOR VARIOUS ROOF 
PITCHES, FROM FLAT ROOF TO 12/12 PITCH 
ROOF.

VENT PIPE

Fig. #43

26

TC36.CE3  250313-48

Summary of Contents for TC36.CARE3

















































Reviews:

No comments