manualshive.com logo in svg

Town & Country Fireplaces TC36.CARE3, Installation And Operating Instructions Manual, Page: 12 / 48

Share
Download
Town & Country Fireplaces TC36.CARE3 Installation And Operating Instructions Manual Download Page 12

Each Kit Contains:

 Item     Part #          Description                 Qty.

  1   5049.9912    SCREW, TEKS 

Pkg 

   

 

#8 x 1/2”  

40

  
    2     9794.2  

STUD, SIDES,  

 

   

 

48”L  

2

 
    3   9794.5  

STUD, OUTER  

 

   

 

SIDES, 48”L  

2

  4   9093.22  

STUD, CENTER,  

 

   

 

15 7/16”L  

2

 
    5   9193.501   STUD, HEADER,  

 

   

 

49 7/8”L  

1

 
  6   9393.001   STUD, PLATE,  

 

   

 

41 1/4”L  

1

    
    7   9194.5  

BASE PLATE ,  

 

   

 

5 15/16”L  

2

  8   9596  

ARCH SUPPORT 

 

   

 

 

2

   

1.   Top Frame Assembly

r

Lay out  side studs (2) and center studs 
(4) on a large flat surface. (Fig #19)

r

Using the screws provided (1), attach the 
header stud (5) and the plate stud (6) to 
the center studs (4).

TC36.BRFRKITA

Fig. #19

1

2

3

4

5

6

7

8

TC36 Arched Steel Stud Framing Kit

2

2

4

5

6

8

8

Attach 
together

Attachment 
point

Attachment 
point

Attachment 
point

12

TC36.CE3  250313-48

Summary of Contents for TC36.CARE3

















































Reviews:

No comments