6
1. Insert the dispenser into the installation
holes in the counter (or the sink).
2. Secure the dispenser with washer and hex
nut.
INSTALLATION PROCEDURE - Spout
INSTALLATION PROCEDURE - Controller
Marking of the positions of the screw holes for the anchoring plate.
Decide the anchoring position of the controller and mark the positions of screw holes on the wall by
referring to the dimensional drawing.
Reference
anchoring screw
1. Drill a rough hole at the screw hole position
and drive in the curl plug (procure in the field).
2. Anchor the bottom anchoring plate to the
controller with one countersunk tapping screw.
Installing the controller on a tiled or concrete wall
[ 0.8 gallon (3L) Tank Type ]
Controller (Back side)
Anchoring plate
Countersunk
tapping screw
ĭPP[PP
Anchoring plate
Countersunk tapping screw
ĭPP[PP
Top side
Bottom side
Reference
anchoring screw
(Unit: Inch (mm))
[ 0.26 gallon (1L) Tank Type (special order)]
Dispenser
Packing
Sensor cord
Washer
Hex nut
Air hose (blue)
Liquid soap hose
(clear)
* Procure a curl plug that matches the screw
ĭPP[PP
Caution
Make sure that the cords and tubes do not get
crimped.
Caution
y
Do not tighten the screws with an electric
screwdriver.
These should be tightened manually.
y
Pay attention not to confuse the top side and
the bottom side of the anchoring plate.
Anchor
PP
PP
PP
PP
PP
PP
PP
PP
(21 mm)
EN
GL
IS
H
7
3. Position and anchor the bracket with two
screws.
Confirm that the wooden wall has a structure that
can sustain the weight (4.41lb) of the controller
(Triple type). (In the case of dry wall, in order to
hold the controller, make sure the plywood base
is more than 1/2" (13 mm) thick.) Anchor the
mounting bracket with two screws and anchor the
anchoring plate with one screw. Reinforce the wall
structure sufficiently as needed.
4. Hang the controller on the mounting bracket
and anchor the bottom anchoring plate with
one screw.
INSTALLATION PROCEDURE - Controller
(Continued)
Dimensions
(Unit: Inch (mm))
[ 0.8 gallon (3L) Tank Type ]
[ 0.26 gallon (1L) Tank Type (special order)]
Controller
Caution
y
Install the unit body horizontally.
y
Pay attention not to pinch of the electric cord or
contact it with edges.
* Sandwich the grounding wire with the
mounting bracket and anchor them with screw.
Installing the controller on a wooden
wall or dry wall
Mounting bracket
Screws
Screw
Anchoring plate
1''
(25 mm)
1''
(25 mm)
3-3/4''
(94 mm)
5-7/8''
(149 mm)
7/16''
(11 mm)
1-7/8''
(47 mm)
2-7/8''
(72 mm)
2-7/8''
(72 mm)
5-7/16''
(138 mm)
1-5/16'' (33 mm)
4-5/8''
(117 mm)
5-7/8''
(149 mm)
1-3/4''
(43.5 mm)
2-7/8''
(72 mm)
7/8''
(22 mm)
4-1/2''
(113.5 mm)
3-3/4''
(94 mm)
1''
(25 mm)
5-7/16'' (138 mm)
7/16''
(11 mm)
5-7/16'' (138 mm)
1-7/8''
(47 mm)
EN
GL
IS
H